HoldBackup
UPS battery backup

Minutes: ride through a flicker, or shut down cleanly.

24 guides

Best picks and comparisons

Start here

Portable power stations

Hours: a charged battery, with no fuel to store.

33 guides

Best picks and comparisons

Start here

Portable generators

Days: as long as the fuel lasts, always outdoors.

57 guides

Best picks and comparisons

Start here

UPS battery backup

Minutes: ride through a flicker, or shut down cleanly.

Portable power stations

Hours: a charged battery, with no fuel to store.

Portable generators

Days: as long as the fuel lasts, always outdoors.

Guide 31 · UPS

How to Choose a UPS Battery Backup for a Pellet Stove

Size the UPS to your stove's own numbers. Its watt rating must cover the stove's highest draw, which is often during ignition. Its battery must also run the fans, auger, and controller long enough to ride out a short outage or let the stove burn down safely. Look for pure sine wave output, and check the stove manual for the maker's backup guidance.

Updated Drafted and checked with AIFact-checked by the HoldBackup editorial team How this guide was madeBased on manufacturer specs and owner reports, not HoldBackup's own testing.

On this page
  1. Start with your stove's numbers
  2. Match the UPS watt rating to the highest draw
  3. Why pure sine wave output matters
  4. Plan runtime around your outages
  5. Setup and upkeep
  6. Sources

Affiliate disclosure: some store links on HoldBackup are affiliate links. If you buy through one, HoldBackup may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. How HoldBackup makes money

The verdict

Buy a pure sine wave UPS, such as the CyberPower CP1500PFCLCD, only after confirming that its continuous watt rating covers your stove's highest draw and that the maker's runtime chart, read at your running load, meets your goal.

See the store link

What we check

  • Watt rating above your stove's highest draw
  • Pure sine wave output
  • Runtime at your running load, from the maker's chart
  • Stove maker's backup guidance in the manual
  • Outlet layout and battery replacement
  • Warranty terms
Compact tower UPS: upright unit on small feet with a narrow front display strip, a lit round power button and two vent slots on its side

Drawing of backup power equipment.

Store link UPS

CyberPower CP1500PFCLCD PFC Sinewave UPS Battery Backup and Surge Protector

One listing to compare. Check its specs against the list above before you buy.

Maker's US pageCyberPower's US page lists it with Purchase Online.cyberpowersystems.com Checked

What owners reportOwners report it works with home server and NAS shutdown software and lasts for years with fresh batteries. Forum owners also say the batteries can give out with no warning from the unit.TrueNAS forum, Unraid forum, The FPS Review forum Checked

PriceAmazon sets it, and it changes. The button takes you to today's price.

Store linkPaid link

The unit named above, on Amazon.

Check price on Amazon

HoldBackup earns a commission if you buy through this link. Amazon sets the price.

Start with your stove's numbers

Every pellet stove draws a different amount of power, so begin with your own stove. Check the rating label, usually on the back or inside a side panel, and the owner's manual. Many manuals list a running draw and a separate igniter draw.

The igniter often pulls the most power, but only for a short time during startup. After that, the stove runs on a lower, steady draw for the combustion fan, the room blower, the auger motor, and the control board. You need both numbers. The higher one sets the minimum watt rating. The lower one sets your runtime.

If the label is unclear, plug the stove into a plug-in watt meter. Watch it through a full startup and then for a while at your usual heat setting.

  • Igniter or startup watts: sets the minimum UPS watt rating
  • Running watts: decides how long the battery lasts
  • Volt-amp (VA) rating: useful, but compare watts first

Match the UPS watt rating to the highest draw

A UPS lists a VA rating and a watt rating. The watt rating is the one to compare against your stove. The number in a model name is not always the continuous output, so check the spec sheet for the actual watt rating.

Leave headroom. A UPS running near its limit has less runtime and may shut down if the load spikes. For example, if your stove's igniter draws 400 watts and it runs at 120 watts, choose a UPS whose watt rating sits well above 400, then check its runtime at 120.

If you won't need to relight the stove on battery, the igniter matters less during an outage. It still matters if the stove tries to restart while on battery, so plan for it.

Why pure sine wave output matters

Pellet stoves use small motors and an electronic control board. Some stove makers say a simulated or stepped sine wave can make motors hum, run hot, or confuse the controller. A pure sine wave UPS gives these loads cleaner power while on battery.

The CyberPower CP1500PFCLCD, the listing on this page, is sold as a sine wave unit. Confirm the output type on the spec sheet for any UPS you consider, and check your stove manual for any waveform requirement.

Plan runtime around your outages

A standard UPS is built to bridge short outages, not to run a stove for a full day. Find the maker's runtime chart and read it at your stove's running watts. That gives you a realistic estimate.

Decide what you want the battery to do. Some owners only need the fans to keep running so the stove can burn down its fire and clear the firebox. Others want to keep heating through a short outage. The second goal takes far more battery.

If your outages often last many hours, a portable power station or a properly installed generator setup may serve you better than a UPS alone.

  • Short goal: keep fans running until the fire burns down
  • Longer goal: keep heating through a brief outage
  • Long outages: consider a larger battery source or generator

Setup and upkeep

Plug the stove directly into a battery-backed outlet on the UPS, not into a power strip or extension cord. Place the UPS where it stays dry, away from the stove's heat and the pellet hopper, with room for air to flow.

Test the setup before winter. With the stove running, unplug the UPS from the wall and confirm the stove keeps running and the UPS does not overload. UPS batteries wear out over time, so check the warranty and how easy the battery is to replace.

Keep working smoke and carbon monoxide alarms in your home, and follow your stove maker's venting and outage instructions.

Sources

Recorded AI check: Oct 9, 2026. The sources below may include later additions. AI checks compare factual numbers and checkable claims with web sources; they do not verify every statement.

Best UPS battery backup for a home and APC vs CyberPower compare units from the makers' numbers. Every guide in this class is in UPS battery backup.

How this guide was made

  1. Drafted and checked with AI. An AI model wrote the draft from the guide's topic. A second AI pass looked for factual numbers to check against web sources. This does not verify every statement. A draft that fails the check is held for review.
  2. Fact-checked by the HoldBackup editorial team. On , a person on the HoldBackup editorial team reviewed this guide against its sources. That is a review of the writing, not a test of any unit.
  3. General guidance only. No prices, rankings, or test results, because we have none to back them. Check any number against the maker's own spec sheet.
  4. No lab tests, and we say so. HoldBackup has not run any unit named here.
  5. The store link is not a pick for this guide. It goes to a unit in this product class that this guide does not review. Check it against the list above before you buy.
  6. Labelled store links. A store button goes straight to Amazon with HoldBackup's affiliate tag. HoldBackup counts the click. A live button carries a "paid link" label, and the disclosure sits above the first one on every guide.

Questions

What size UPS do I need for a pellet stove?

Find your stove's highest draw, usually during ignition, and choose a UPS whose continuous watt rating sits comfortably above it. Then read the maker's runtime chart at your stove's running draw to see how long it will last.

Do I need a pure sine wave UPS for a pellet stove?

It is the safer choice. Pellet stoves have motors and a control board, and some stove makers advise against stepped or simulated sine wave power. Check your stove manual for its requirement.

How long will a UPS run a pellet stove?

It depends on your stove's running draw and the UPS battery. Use the UPS maker's runtime chart at your measured load. A standard UPS is meant for shorter outages, so plan another power source for long ones.

Can I plug other devices into the same UPS?

You can, but every added device cuts runtime and adds to the load during ignition. Keep the stove's battery outlet for the stove if heat is your priority.

Where does the price button go?

Straight to Amazon. Amazon sets the price and availability, and both can change.

More guides

  1. UPS

    Can a UPS battery backup run a refrigerator during an outage?

    Most desktop UPS units are not built for a fridge compressor. See which ratings to check and how to find your refrigerator's real draw.

  2. UPS

    A UPS for your router and modem

    How a small battery backup can keep Wi-Fi up through short outages.

  3. UPS

    Choosing a 1500VA Sine Wave UPS for a Home Office

    Plan which office devices share battery power, check the SMT1500C capacity, and separate SmartConnect monitoring from automatic computer shutdown.

  4. UPS

    Choosing a Pure Sine Wave UPS for a Home Network Closet

    Map your ONT, router, switches and access points before sizing a network UPS. Check PR1500LCD specifications, runtime and monitoring requirements.

Browse all guides